Importing addresses from a text file
A question on the mail-list asked about how to import a series of addresses from an external file. One of the ways to do this would be with some kind of database, although for simpler projects, creating the database, then creating the script to use it would be too much work.
This script, importadd.py, uses a simple text file with a particular format, parsing the addresses and then creating a text frame for each. As written, the script opens a new document, then creates new pages. One could modify it to make use of an existing document, or not only place these addresses, but also other page elements as you go, such as the mass mailing envisioned by the List questioner.
The format of the address text file is that it begins immediately with the first address, and the address is laid out as it will be on the page. After the address, there is a single blank line separating it from the next address. This is important because this blank line -- and it must be a blank line and no characters -- is the flag to tell the script that the address is finished, go ahead and make a new page, make a text frame and put the address in it.
Here is the script:
#!/usr/bin/env python
# -*- coding: utf-8 -*-
"""
File importadd.py
Created 2007-02-17
Gregory Pittman
imports addresses from text file
puts them in text frame
adds new pages as needed
The format for addr.txt is a plain text file beginning with the first address,
one line of the file for each line of the address. No blank lines inside the
address, and a single blank line between the addresses and *two* blank lines after
the last address.
"""
import scribus
if scribus.newDoc(scribus.PAPER_LETTER, (10,10,20,20),scribus.PORTRAIT, 1, scribus.UNIT_POINTS, scribus.NOFACINGPAGES, scribus.FIRSTPAGERIGHT):
file = open('addr.txt', 'r')
add = ''
page = 0
while 1:
info = file.readline()
if not info: break
if info != '\n':
add = add + info
else:
if page:
scribus.newPage(-1)
A = scribus.createText(60, 100, 200, 100)
scribus.setText(add, A)
scribus.setTextAlignment(scribus.ALIGN_LEFT, A)
scribus.setFont("Luxi Sans Regular", A)
scribus.setFontSize(12, A)
add = ''
page = page + 1
Notes
- One of the rigid features is that the text file must be named addr.txt, but one could easily add a FileDialog to be able to input a filename. So, before the line:
file = open('addr.txt', 'r')
you could add this (with or without this filter for files ending in '.txt'):
selectfile = scribus.fileDialog("Select Your Address File", "*.txt")
then modify the next line:
file = open(selectfile, 'r')
- The page variable is there only to make sure that a new page isn't created at the beginning, since we already did that with the scribus.newDoc command.
- In case you're wondering why this readline and concantenation works without inserting carriage returns, it's because Python reads in a newline at the end of each line. This also explains why the test for a blank line looks for '\n'.
- This while 1: construct looks rather clumsy, since we just get out of the while loop with a break command, but it's shown as an example in the Python text I use as a reference. Similarly, we didn't file.close() but relied on the fact that the script was done at that point -- considered acceptable in Python.
- The scribus.createText variables are (x, y, width, height), where x and y refer to the upper left hand corner of the frame, and units are points for this script, but are taken from the scribus.newDoc command.
- The whole script will fail if you're not running it from Scribus, and yes, you could use something like
try:
import Scribus
.
.
.
else:
with a message to tell people to use it in Scribus, but really, no one gets hurt if it fails. I try to keep the coding as concise as I can. I think it's good to learn how to understand the Traceback messages that Python generates -- not likely to be the last time you see one.
An Example Address File
- Once again, the file should contain nothing other than the addresses. The blank line between addresses has no other characters -- it needs to satisfy this if info != '\n' test (technically, needs to fail the test) in order to recognize that the address has finished. For this reason, there also needs to be two blank lines at the end, and there can be no blank lines in the middle of the address. Note the need for two blank lines at the end -- perhaps the way that Python reads EOF.
- The addresses came from a website showing formats for postal addresses to various countries, so as far as I know do not identify any living persons.
Monsieur Jean Durand 25 Rue des Fleurs 33500 LIBOURNE FRANCE Sr. D. Alvaro Blanco Ruiz Luna 10 - 3° 28300 ARANJUEZ (MADRID) SPAIN John Smith 100 MAIN ST PO BOX 1022 SEATTLE WA 98104 USA Herrn Ebelhard Wellhausen Wittekindshof Schulstrasse 4 32547 Bad Oyenhausen GERMANY Sig. Mario Rossi Viale Europa, 22 00144 ROMA, RM ITALY M. Andrée TROMMER BP 5019 L-1050 Luxembourg LUXEMBOURG Mr. Walter C. Brown 49 Featherstone Street LONDON EC1Y 8SY ENGLAND